Produkten har blivit tillagd i varukorgen
Moms visas:

Synthesis technology E350 morphing terrarium

3 600 kr
Finns i lager
Finns ej i lagret
Finns ej i lagret
Bevaka produkt

Ange din e-postadress nedan så meddelar vi dig när produkten finns i lager!

Synthesis technology e350 morphing terrarium is a unique wavetable vco with 2 independent waveform outputs. unlike similar designs, the e350 is a fully self-contained, 1v/oct vco. what sets the e350 apart from previous wavetable oscillators is the voltage-controlled morphing.
The module comes shipped with 3 banks of 64 'basic' waveforms (192 total). each bank of 64 waves is arraigned in memory as an 8 x8 array (like a chess board). the 'rows' are called 'the x direction' and the columns are 'the y direction'. the 2 panel controls and the 2 external control voltages (morph x and morph y) are used to "point" to where in the array we use for the data that is the xy out. the third control voltage is called 'z morph', and it determines the waveshape at the z out. the z control voltage 'scans' then wavetable bank from wave #1 (think as row 1, column 1) to wave #64 (row 8, column 8). for example: if x morph is set to 2, and y morph is set to 5, the signal at xy out is the waveform stored at row 2, column 5 (the 13th wavetable). the z out is completely independent of xy out, so if the morph z knob is at 48, then the 48th wavetable (row 6, column 8) is the output.
The wavetables in the 3 banks are very carefully ordered by rows. in general, scanning in the x direction will generate a smooth progression of timbre. each row, however, is different! there are sine banks, pulse width modulations, filtered noise and even male/female vocal formants. so, then you can see that scanning in the y direction (in a column) will be extremely varied. and the beauty is that you can scan in both directions simultaneously if you want.
But we were not content with just indexing through the table 1 wave at a time. instead, the e350 implements a proprietary smoothing/anti-aliasing algorithm that allows the 2 outputs to be a continuous blending of one wave to another. the algorithm calculates 128 "in-between" waveforms, so that the 192 'basic' waveforms are really expanded to over 24 *thousand* individual timbres! so as you adjust the panel controls, or add external modulation (from lfos, eg, etc) the e350's outputs are "glitch-free" and will provide you with a near infinite range of tonal possibilities. for people that like the glitches of older wavetable vcos, there is a jumper option on the pc board to add these back in.
But, we wanted to do more, so we added a 3-position range switch for using the e350 as the world's best lfo. at the lowest setting, the e350 will cycle once every 13 minutes and be repeatable within 20usec. the sync signal can be used to reset both outputs to zero ('hard sync') like any other vco. the 'c' bank of waveforms are specifically designed to be used in lfo settings (although they will output audio timbres as well). the lfo waveshapes are everything from 'chirps', sequences of individual notes to noise gates, s&h effects to exponential/log sweeps. like quadrature outputs? the e350 can have variable phase outputs under cv control.
There is nothing like the e350 in any modular format. in many patches a vcf is not needed: the timbres that are generated are already smooth and harmonically "correct". from the precise tracking to over 24,000 waveforms possible, the e350 sets the standard in modular oscillators.
• size: 3u x 14hp (128.5mm x 70.8mm)
• depth: 47mm
• power: 14-pin doepfer (55ma for +12v, 25ma for -12v) and 4-pin motm (45ma for +15v, 15ma for -15v)
• cv input range: -5v to +5v
• audio output: 10v pk-pk nominal
• frequency range: 1 cycle in 13min to 10khz in 3 ranges
• coarse/fine - initial frequency of the vco
• fm: attenuates the voltage on the fm jack 0-100%
• morph x - sets the starting point of the xy out waveshape in a row
• morph y - sets the starting point of the xy out waveshape in a column
• morph z - sets the starting point of the z out waveshape (scans the entire bank)
• bank - selects the a (sine/hammond organs), b (widely varies) or c (lfo shapes/noise) wavetable bank
• range - selects the operating range of the vco frequency
• 1v/oct - 1 volt/octave control for the initial vco pitch
• fm - frequency modulation input (dc to 8khz)
• sync - resets vco when the input signal exceeds 0.6v
• morph x - this cv is added to the panel control
• morph y - this cv is added to the panel control
• morph z - this cv is added to the panel control
• xy out - the waveshape calculated by the morph x and morph y settings
• z out - the waveshape calculated by the morph z setting

E350 morphing terrarium
Lägg i önskelista


2015-08-23 av
Hej -- kan du bestille en e350 hjem til mig? vh Mark Lorenzen/København



tumblr site counter